Thompson F.D.

Thompson F.D.

Flickr Album Gallery Powered By: WP Frank

Project Description

Client: Thompson F.D.
Year Completed: 2018

New Pierce Engine for Thompson Fire Department, Thompson, Ohio. Prior to the truck arriving at Sensible Products, all new equipment to be mounted on the truck was shipped to Sensible Products and housed in a staging area until the truck arrived. Once the truck arrived at Sensible Products some existing equipment was brought with the truck and an equipment mounting plan was determined. In the first drivers side compartment, water flow equipment was mounted in the upper portion of the compartment on the existing peg board. All LDH fittings, small couplings, adapters, wrenches, and span-hammer were mounted. In the lower portion of the compartment, two small vertical slide outs were removed and a black poly floor board was mounted on the slide out tray. The BlitzFire was then mounted and secured with a strap. In the second drivers side compartment, a Chanl Panl rear wall board was mounted and a black poly floor board with aluminum lip was mounted. On the Chanl Panl board, a halligan, sawzall, flat head axe, pick head axe, and saw blades were mounted. On the floor of the compartment, a set of irons were mounted. In the third drivers side compartment, a Chanl Panl wall board was mounted in the upper portion of this compartment and air bags and control kit were secured with straps. In the lower portion of this compartment, a black poly floor board was mounted to the slide out tray and a cutter, spreader, rams, and power unit were mounted. The cutter and spreader are in custom made brackets and the rams are secured in plastic welded wells. In the rear compartment, cribbing bags were secured with a strap. In the third passengers side compartment, a Chanl Panl rear wall board was mounted and cord adapters and landing zone plates and lights were mounted. The landing zone plates were mounted in a pocket and the landing zone lights were mounted using custom magnetic brackets. The lights simply lift off/on the magnetic surface. In the lower portion of this compartment, a generator and cord reel were secured. In the second passengers side compartment, a black poly floor board with aluminum lip was added. This area was left open for the tool box, tarps, etc. In the first passengers side compartment, a custom welded box was made to hold flares that sat on the shelf next to the cones. In the lower portion of this compartment on the slide out tray a custom plastic welded divider was made to hold extinguishers in the front and foam in the back. In two small compartments behind the cab, a divider was made to hold and separate chains and hydraulic oil and a gas can in the other compartment. A pike pole was mounted on the exterior of the truck. In the cab, a custom map box was made with 3 removable dividers and a space for a box of gloves and a cup holder on the passengers side. All equipment was labeled with red/white tags. This truck was completed in 5 days.

 

Go In-Service

  • Match your equipment to our mounting products listed in our catalog. Custom mounts are available upon request. We will ship all mounting products complete along with mounting hardware. This will allow you to plan, layout, and mount all equipment at your facility.
  • Contact us for help designing boards or configuring cabinets based on your equipment list. We will ship complete boards to you, ready for installation.
  • Send us your apparatus and accompanying equipment and we will do all the layout, fabrication, and installation. Your apparatus will be completely outfitted and ready to Go In Service when it leaves our facility! Contact us for outfitting large fleets as well.

South Central F.D.

South Central F.D.

Flickr Album Gallery Powered By: WP Frank

Project Description

Client: South Central F.D.
Year Completed: 2018

New Rosenbauer for South Central Fire District, Fredericksburg, OH. Sensible Products visited the Fire Department to look at the new apparatus prior to it arriving at Sensible Products for equipment mounting. Sensible Products worked with the committee to come up with an equipment mounting plan. Once the apparatus arrived at Sensible Products, the equipment mounting plan was reviewed and work began. This truck had a lot of shelves and panels that were ultimately removed to make better use of the space for the equipment they were carrying. This is why we stress to plan for the equipment to be carried when specing out the truck. In the first drivers side compartment, one of the aluminum panels was cut in half and several small shelves were removed from this compartment. Chanl Panl boards were added to the rear wall and both sides of the vertical slide out board. All water flow equipment including LDH fittings, smaller couplings and adapters were mounted on the rear wall and slide out vertical board. Nozzles were mounted on the floor next to the vertical slide out board. A plastic welded divider was made to hold several hose rolls. The top of this divider provided another platform where the additional wyes and valves were mounted. In the second drivers side compartment, the existing out/down slide out unit was lowered and an additional shelf was added in the back top area of this compartment to hold light duty equipment. On the out/down slide out unit a black poly floor board and back board were added and a chain saw, rotary saw, fuel mix, and saw parts pocket were mounted. In the third drivers side compartment, the existing box to hold SCBAs and one shelf were removed from this compartment. Black poly floor boards were added to the floor and remaining shelf and Chanl Panl boards were mounted on both sides of the vertical slide out board. On the shelf, a cord reel and lights were mounted, and underneath that shelf a plastic welded divider with strap was mounted to hold 4 fire extinguishers. On the Chanl Panl vertical slide out board and side walls, extra tool handles, shovels, claw tools, and broom heads were mounted. In the rear compartment of the apparatus, a black poly floor board was mounted on the slide out unit and a PPV fan and generator were secured. The salvage tub/tarps went above the fan and generator on a shelf. On the top of the apparatus, a plastic welded divider was made to hold a Little Giant Ladder. In the third passengers side compartment, several shelves were removed to better accommodate the equipment. A Chanl Panl rear wall board was added and several tool heads and a K-tool were mounted. In the lower section of this compartment, 2 plastic welded boxes were made to hold chains and chimney kit. In the second passengers side compartment, all hand tools were mounted on the existing peg board. Tools included: NY hook, pike pole, irons, pick head and flat head axe, sledge hammer, halligan, bolt cutters, and pry bar. A black poly floor board was also added in this compartment. In the first passengers side compartment, a Chanl Panl board was mounted to the rear wall and SCBAs and Rit Pack were remounted to the wall. The bottom slide out tray is open for future equipment. In the cab, a Chanl Panl board was mounted to mount 2 Streamlights. All equipment was labeled with red/white tags. This truck was completed in 5 days.

 

Go In-Service

  • Match your equipment to our mounting products listed in our catalog. Custom mounts are available upon request. We will ship all mounting products complete along with mounting hardware. This will allow you to plan, layout, and mount all equipment at your facility.
  • Contact us for help designing boards or configuring cabinets based on your equipment list. We will ship complete boards to you, ready for installation.
  • Send us your apparatus and accompanying equipment and we will do all the layout, fabrication, and installation. Your apparatus will be completely outfitted and ready to Go In Service when it leaves our facility! Contact us for outfitting large fleets as well.

Jackson Twp. FD

Jackson Twp. FD

Flickr Album Gallery Powered By: WP Frank

Project Description

Client: Jackson Twp. F.D.
Year Completed: 2018

New Sutphen Rescue Pumper for Jackson Twp. Fire Department, Massillon, Ohio. Sensible Products visited the Fire Department prior to the truck arriving at Sensible Products to look at the truck and provide a detailed quote based on the equipment mounting plan. Once the truck arrived at Sensible Products the plan was reviewd and work began. In the first drivers side compartment, an existing shelf was lowered to better accommodate the equipment. Chanl Panl rear and side wall boards were mounted in the upper portion of this compartment and a black floor board was mounted on the shelf. All LDH fittings, small couplings, spanners, and a mallet were mounted. On the shelf, several nozzles and a gated wye were mounted. On the lower slide out tray, a black plastic welded divider was mounted to secure and separate pro-pak foam, extinguishers, and an SCBA. In the second drivers side compartment, an existing slide out/down tray was lowered to better accommodate the equipment. On this out/down tray, a black poly floor board was added and the Kodiak Jacks were secured. In the lower portion of this compartment, a black plastic welded divider was added to hold the air bags, control kit, air chisel, and chains. The air bags were secured down with a Velcro strap. In the third drivers side compartment, the existing shelf was moved up to better accommodate the extrication equipment and battery chargers that would mount on the shelf. In this compartment, the customer supplied Lazy Susan from Fire & Marine Inc. was mounted on the slide out tray to hold a cutter, spreader, and ram. A black poly floor board was added to the slide out tray. Chanl Panl was mounted on the rear and side walls to mount a sawzall and barrier tape. In the rear of the apparatus, a black poly floor board was mounted on the slide out tray and an electric fan, portable lights, and cords were mounted. In the upper hose bed area, a plastic welded divider was made to hold brooms, a hook, and 4 x 4s. In the third passenger side compartment, a Chanl Panl rear wall board was mounted in the upper portion of this compartment and step chocks and ratchets/straps were mounted. In the lower portion of this compartment on the slide out tray, a black plastic welded divider was mounted to hold cribbing bags and rocker panel plates. In the second passengers side compartment, a custom swing out panel made by Sensible Products Inc. was made and installed to mount hand tools. The swing out panel was made of Chanl Panl boards complete with stoppers/locks and a grab handle. A Chanl Panl board was mounted on the rear wall of this compartment. Tools mounted on the swing out and back wall included: flat head axe, pick head axe, halligan, 2 bolt cutters, fan bar, cable cutters, K-tool, shovels, hand saw, 2 sledge hammers, pry bar, and extra saw blades. A black poly floor board was also mounted in this compartment. In the first passengers side compartment, a Chanl Panl rear wall board was mounted in the upper portion of this compartment. Two saws were mounted, along with a bracket for a fuel can. A shelf was added to the middle portion of this compartment to hold tarps and a pocket for saw parts. In the lower portion of this compartment on the slide out tray, a black poly floor board was mounted. A tool box and portable winch were mounted. In the behind the cab compartments, Turtle Tile was added to the floor and one compartment had two hooks for gear/helmets. In the cab, a custom plastic welded box was made to hold the Lucas Chest Compression System bag. All equipment was labeled with red/white tags. This truck was completed in 6 days.

 

Go In-Service

  • Match your equipment to our mounting products listed in our catalog. Custom mounts are available upon request. We will ship all mounting products complete along with mounting hardware. This will allow you to plan, layout, and mount all equipment at your facility.
  • Contact us for help designing boards or configuring cabinets based on your equipment list. We will ship complete boards to you, ready for installation.
  • Send us your apparatus and accompanying equipment and we will do all the layout, fabrication, and installation. Your apparatus will be completely outfitted and ready to Go In Service when it leaves our facility! Contact us for outfitting large fleets as well.

Rome F.D.

Rome F.D.

Flickr Album Gallery Powered By: WP Frank

Project Description

Client: Rome F.D.
Year Completed: 2018

New Toyne Tanker for Rome Volunteer Fire Department, Rome, OH. Sensible Products visited the Fire Department prior to the truck arriving at Sensible Products to develop an equipment mounting plan and provide a detailed quote. Once the truck arrived at Sensible Products, the equipment mounting plan was reviewed and work began. In the first drivers side compartment, all water flow equipment was mounted. The upper portion of this compartment had existing peg board in place. Some LDH fittings, wrenches, and lights were mounted on the peg board. On the shelf in this compartment, nozzles and wyes were mounted. In the lower portion of this compartment, a plastic welded cubby compartment and aluminum shelf were added to mount all rural water supply appliances. This made all equipment easily accessible and visible. On the right side door, Chanl Panl was mounted and the 6″ storz fittings and smaller couplings were mounted. On the left side door, hammers, mallets, and a portable light were mounted.  In the second and third drivers side compartments, all forcible entry tools were mounted. Chanl Panl was added to the back walls of both compartments. All tools including: claw tool, flat head axe, pick head axe, sledge hammer, GlasMaster, pike pole, two bolt cutters, pry bar and halligan were mounted. Black poly floor boards were added and a rotary and chain saw were mounted. Also in this area, two custom roll down vinyl covers were mounted to protect the side of the truck when moving tools in and out of the compartments. The covers are rolled up and stored in the compartment when not in use and fold out 12″ to cover the side of the truck down to the wheel well. In the forth drivers side compartment, Chanl Panl was added to the upper section of this compartment and two SCBAs were mounted. Also in this area, posts were made for the CamLok fittings to sit on, on the shelf. On the passengers side first compartment, two fans, generator, and sawzall were secured with straps. Three custom mounts to hold three sizes of extra sawzall blades were mounted to the door. In the second passengers side compartment, a black poly floor board with a plastic welded divider was installed to secure and separate fire extinguishers, cones, and foam. All equipment was labeled with red/white tags. This truck was completed in 4 days.

 

Go In-Service

  • Match your equipment to our mounting products listed in our catalog. Custom mounts are available upon request. We will ship all mounting products complete along with mounting hardware. This will allow you to plan, layout, and mount all equipment at your facility.
  • Contact us for help designing boards or configuring cabinets based on your equipment list. We will ship complete boards to you, ready for installation.
  • Send us your apparatus and accompanying equipment and we will do all the layout, fabrication, and installation. Your apparatus will be completely outfitted and ready to Go In Service when it leaves our facility! Contact us for outfitting large fleets as well.

Wooster Twp F.D.

Wooster Twp. FD 2018

Flickr Album Gallery Powered By: WP Frank

Project Description

Client: Wooster Township F.D.
Year Completed: 2018

New KME for Wooster Twp. Fire Department, Wooster, Ohio. Sensible Products Inc. met with the Fire Department prior to the truck arriving at Sensible Products to discuss an equipment mounting plan. Once the truck arrived at Sensible Products a definite equipment mounting plan was put in place based on the equipment on the truck. On the drivers side near the pump panel where there was existing PAC Trac installed, a set of spanners and a mallet were mounted. In the first drivers side compartment, a Chanl Panl rear wall board was mounted and a Masterstream, several nozzles, flares and elevator keys were mounted. A custom plastic welded box was made to hold sprinkler tools. In the lower section of this compartment, a black poly floor board was mounted and a custom plastic and aluminum slide out tray was installed. On the tray were several water flow appliances. In the second drivers side compartment, PAC Trac was already installed on the rear wall from the manufacturer. Sensible Products used their water flow mounts to mount several LDH fittings, couplings, adapters, caps, nozzles, and a piercing nozzle. In the third drivers side compartment, a Chanl Panl rear wall board was added and 5 fire extinguishers were mounted. In the lower portion of this compartment, a black poly floor board was mounted and a chain and rotary saw were mounted along with a post for extra saw blades. In the rear of the apparatus, a black poly floor board was added and 2 fans and a fan bar were mounted. A small half shelf was also added in this area to hold the hydrant bag. In the fourth passengers side compartment, the existing top shelf was lowered and a Chanl Panl rear wall board was mounted. In this area the high lift jack, Kodiak jacks, chains, and hand pump were mounted. On the middle out and down slide out unit, a black poly floor board was mounted and a 2 rams were mounted with plastic welded dividers. On the lower slide out, a black poly floor board was mounted and a cutter, spreader, and generator were mounted. A custom plastic welded bracket was mounted on the back wall to hold hoses. Nothing was mounted in the third passengers side compartment, as everything was already organized and labeled. In the second passengers side compartment, Chanl Panl was mounted to both sides of the vertical slide out and a pipe wrench, 2 bolt cutters, pike pole, alligator tool, claw tool, cords/adapters, and 2 barrier tape were mounted. Also in this area a Little Giant Ladder, pry bar, portable light, crash axe, and small sledge hammer were mounted. In the first passengers side compartment, air bags were secured in the top area of the compartment. Traffic signs were mounted on  a black poly board on the underneath side of the shelf up and out of the way with mounting clips for easy access. In the cab area, PAC Trac was already installed in some areas for mounting. On the PAC Trac, Sensible Products mounted a flat head axe, sledge hammer, halligan, and AED. Also in the cab, Sensible Products fabricated a plastic welded map/storage box that mounted to the dog house to hold clip boards, notebooks, and a Ipad. All equipment was labeled with red/white tags. This truck was completed in 4 days.

 

Go In-Service

  • Match your equipment to our mounting products listed in our catalog. Custom mounts are available upon request. We will ship all mounting products complete along with mounting hardware. This will allow you to plan, layout, and mount all equipment at your facility.
  • Contact us for help designing boards or configuring cabinets based on your equipment list. We will ship complete boards to you, ready for installation.
  • Send us your apparatus and accompanying equipment and we will do all the layout, fabrication, and installation. Your apparatus will be completely outfitted and ready to Go In Service when it leaves our facility! Contact us for outfitting large fleets as well.

Valley City F.D.

 

Valley City F.D.

Flickr Album Gallery Powered By: WP Frank

Project Description

Client: Valley City F.D.
Year Completed: 2018

2014 Pierce Velocity Engine for Valley City Fire Department, Valley City, OH. Valley City Fire Department contacted Sensible Products for a quote on equipment mounting, some clean up, and fix up on their Engine. Some equipment on the apparatus was already mounted, but the FD wanted some equipment rearranged and some new equipment was added. In the first drivers side compartment, the existing equipment, including some nozzles and water flow equipment was removed and put in a different compartment. A Chanl Panl wall board was added in the upper section and barrier tape, a mallet, and an SCBA were mounted. In the lower section of this compartment, a slide out with an aluminum tray was added and the generators and cords were secured. Turtle Tile was added to the slide out tray. Portable lights were hung on the wall in this compartment. In the second drivers side compartment, plywood was already installed on the back wall of this compartment, which was left in place and the equipment was rearranged. Sensible Products provided new mounting brackets and mounted all LDH fittings, smaller couplings and adapters, nozzles/wyes, and foam eductor. In the third drivers side compartment, a Chanl Panl wall board was added in the upper section of this compartment and air bags and air bag control kit were mounted. In the middle of this compartment, a slide unit was moved from the other side of the apparatus and put in this compartment to hold the Res-Q- Jacks which were secured with straps. In the lower portion of this compartment, custom mounts for a spreader, cutter, and ram were mounted on the existing slide unit. In the rear of the apparatus, some equipment was relocated and labeled. In the third passengers side compartment, some existing equipment was moved and the slide unit from the floor of this compartment was removed and relocated to the other side of the apparatus ( for the extrication tools).  A chain and rotary saw were mounted and a pocket for saw parts was provided. In the lower section of this compartment where the slide unit was, a plastic welded divider was made to hold cribbing. In the second passengers side compartment, all hand tools were already mounted, just a few needed rearranged and added to this compartment. All tools were re-labeled with red/white tags. In the first passengers side compartment, a Chanl Panl rear wall board was added in the upper section of this compartment and a mallet and RIT pack were mounted. In the lower portion of this compartment, a plastic welded divider was made to hold three extinguishers and a tool box. All equipment was labeled with red/white tags. This truck was completed in 2 days.

 

Go In-Service

  • Match your equipment to our mounting products listed in our catalog. Custom mounts are available upon request. We will ship all mounting products complete along with mounting hardware. This will allow you to plan, layout, and mount all equipment at your facility.
  • Contact us for help designing boards or configuring cabinets based on your equipment list. We will ship complete boards to you, ready for installation.
  • Send us your apparatus and accompanying equipment and we will do all the layout, fabrication, and installation. Your apparatus will be completely outfitted and ready to Go In Service when it leaves our facility! Contact us for outfitting large fleets as well.

South Euclid F.D.

 

South Euclid F.D.

Flickr Album Gallery Powered By: WP Frank

Project Description

Client: South Euclid F.D.
Year Completed: 2018

New Sutphen for South Euclid Fire Department, South Euclid, OH.  Sensible Products worked with the Fire Department before the truck arrived at Sensible Products to determine an equipment mounting plan. South Euclid FD put the equipment mounting process into the specification of the apparatus so it was paid for with the purchase of the apparatus.  In the first drivers side compartment, Chanl Panl boards were installed on the rear and side walls to mount water flow equipment including LDH fittings, smaller couplings, barrier tape, hydrant gates, nozzles, and a mallet. In the lower portion of this compartment, a black poly floor board was added and a portable monitor base was secured. On the vertical slide outs in this compartment, Chanl Panl was added to both sides and hand tools including: irons, TNT tool, bolt cutters, pike pole, and a piercing nozzle were mounted. On the left and right side of this compartment, two sledge hammers, pry bar, shovel and broom were mounted. In the rear of the apparatus, a strap was added for mounting a rotary saw. In the third passengers side compartment, Chanl Panl was added to the rear wall of the upper portion of this compartment and mounts for hoses and a GlasMaster were added. In the lower portion of this compartment, two extrication tool mounts were mounted. In the second passengers side compartment, a Chanl Panl rear wall board was mounted and three fire extinguishers were secured with straps. In the first passengers side compartment, a Chanl Panl board was added to the rear wall and a portable light and hydrant wrench were mounted. In the small, behind the cab compartments, an SCBA, pick head axe, irons, and extinguisher were mounted. Also in this area, a roof hook and trash hook were secured. In the cab, a custom mount for a gas meter was mounted. This truck was completed in 2 days.

 

Go In-Service

  • Match your equipment to our mounting products listed in our catalog. Custom mounts are available upon request. We will ship all mounting products complete along with mounting hardware. This will allow you to plan, layout, and mount all equipment at your facility.
  • Contact us for help designing boards or configuring cabinets based on your equipment list. We will ship complete boards to you, ready for installation.
  • Send us your apparatus and accompanying equipment and we will do all the layout, fabrication, and installation. Your apparatus will be completely outfitted and ready to Go In Service when it leaves our facility! Contact us for outfitting large fleets as well.

Lexington Twp. F.D.

 

Lexington F.D.

Flickr Album Gallery Powered By: WP Frank

Project Description

Client: Lexington Township F.D.
Year Completed: 2018

New Rosenbauer ladder for Lexington Twp. FD, Alliance, OH. Sensible Products Inc. visited the Fire Department to meet with their committee to come up with an equipment mounting plan on their new apparatus. Once the apparatus arrived at Sensible Products there was already a plan in place. In the first drivers side compartment, two (2) Chanl Panl boards were mounted, one on each side of the slide out panel.  All LDH fittings and couplings were mounted on the Chanl Panl board with space left for additional fittings. Nozzles, gated wye, and mallet were all mounted in this compartment. In the second drivers side compartment, three (3) small shelves were removed and re-installed in another compartment. A plastic welded divider was fabricated to hold hose rolls with a fixed top surface that mounted the float dock strainer  and low level strainer. Space was left in the divider assembly to hold fire extinguishers, secured with a strap. A barrel strainer was mounted on the wall in this compartment. In the third drivers side compartment, a black poly floor board was installed and a chain and rotary saw were mounted.  The current shelf in this compartment was reworked and moved up and to the back of this compartment. A trash hook was mounted on the front of the shelf for easy access. Also in this compartment, a pocket for saw parts was mounted, mixed fuel can bracket was mounted, and a post for extra saw blades was mounted. In the fourth drivers side compartment, the three (3) shelves from the first compartment were relocated and installed here. Hooks were supplied for the ladder belts. On the passengers side, compartments one and two were reconfigured to accommodate current equipment. Shelves were repositioned and lowered. Chanl Panl was installed on rear and side walls of this compartment. A black poly floor board was installed. All tools were mounted here including: flat head axe, sledge hammer, pry axe, irons, halligan, and trash hook. In the third passengers side compartment, a plastic welded divider was added and mounts for cords and cord adapters were added. In the cab of apparatus, two portable lights were mounted. On the ladder tip, a pike pole and axe were mounted. All equipment was labeled with red/white engraved tags. This truck was completed in 2 1/2 days.

 

Go In-Service

  • Match your equipment to our mounting products listed in our catalog. Custom mounts are available upon request. We will ship all mounting products complete along with mounting hardware. This will allow you to plan, layout, and mount all equipment at your facility.
  • Contact us for help designing boards or configuring cabinets based on your equipment list. We will ship complete boards to you, ready for installation.
  • Send us your apparatus and accompanying equipment and we will do all the layout, fabrication, and installation. Your apparatus will be completely outfitted and ready to Go In Service when it leaves our facility! Contact us for outfitting large fleets as well.

Kidron F.D.

Kidron F.D.

Flickr Album Gallery Powered By: WP Frank

Project Description

Client: Kidron F.D.
Year Completed: 2018

New 4-Guys Engine for Kidron Fire Department, Kidron, OH. Sensible Products worked with the Fire Department to come up with an equipment mounting plan before the truck arrived at our facility and once the truck was delivered. In the first drivers side compartment, Chanl Panl was added to the rear and side walls to mount all water flow equipment. A Sensible Products yellow hand control box was mounted to better hold the Wilburt hand controller. An aluminum shelf was added here and a black poly floor board was mounted on the shelf. All nozzles/wyes/foam tubes were then mounted on the shelf. A portable monitor base and cones were housed under the shelf. In the second drivers side compartment, a black plastic welded divider liner was added to hold and separate cribbing, air bags, air bag control kit, and a sawzall. In the third drivers side compartment, a fixed shelf was added and a black poly floor board was mounted on the shelf. A Chanl Panl rear wall board was added to hold the Kodiak Jacks, accessories, and hoses. Custom brackets were made for the side walls to hold a crash kit, a cutter, and spreader. A plastic welded divider liner was made for the existing slide out tray to hold all the extrication accessories. In the rear of the apparatus, a small Chanl Panl board was added to the rear wall to hold other water flow equipment. Stoppers were made to hold the rural hitch and hose rolls in place. In the third passengers side compartment, an additional shelf was added and a black poly floor board was mounted to it along with a chain and rotary saw. A Chanl Panl rear and side wall board were added to hold a pocket for saw parts, TruFuel cans, and extra saw blades. In the second passengers side compartment, two portable lights were mounted. The rest of the area was left open for tarps and miscellaneous. In the first passengers side compartment, another aluminum shelf was added to hold SCBAs and spare bottles. An aluminum divider was added to secure four spare bottles in a vertical position. In the lower portion of this compartment, a PPV fan, generator and gas can were secured. Both the drivers and passengers side of the apparatus had tall compartments behind the cab the department wanted to use for all of their tool storage. In the drivers side, Chanl Panl boards were added to the rear and side walls and a claw tool, trash hook, bolt cutters, NY Hook, sledge-wedge, pick head axe, irons and two extinguishers were mounted. In the passengers side compartment, rear and side wall Chanl Panl boards were added and a flat head axe, sledge-wedge, halligan, sledge hammer, two NY hooks, battering ram, and two extinguishers were mounted. With both of these compartments being so tall, all tool brackets were mounted low for easy, yet secure accessibility. Most D-handled tools were hung on a D-handle bracket up high, with an additional mount lower on the tool within arms reach. All equipment was labeled with red/white tags. This truck was completed in 4 1/2 days.

Go In-Service

  • Match your equipment to our mounting products listed in our catalog. Custom mounts are available upon request. We will ship all mounting products complete along with mounting hardware. This will allow you to plan, layout, and mount all equipment at your facility.
  • Contact us for help designing boards or configuring cabinets based on your equipment list. We will ship complete boards to you, ready for installation.
  • Send us your apparatus and accompanying equipment and we will do all the layout, fabrication, and installation. Your apparatus will be completely outfitted and ready to Go In Service when it leaves our facility! Contact us for outfitting large fleets as well.

Geneva F.D.

Geneva F.D. 2018

Flickr Album Gallery Powered By: WP Frank

Project Description

Client: Geneva F.D.
Year Completed: 2018

Sutphen Pumper for Geneva Fire Department, Geneva, OH. Sensible Products Inc. worked with the Chief and committee to determine an equipment mounting plan once the apparatus arrived at Sensible Products. In the first drivers side compartment, Chanl Panl boards were added to the rear and side walls and all water flow equipment including LDH fittings, couplings, adapters, and nozzles were mounted. An SCBA was also mounted. In the lower portion of this compartment, a black plastic welded divider liner was mounted to separate hose rolls. No equipment was mounted in the second drivers side compartment, only labels. In the third drivers side compartment, an aluminum divider was added to the slide out tray to separate and secure a fan and three fire extinguishers. Chanl Panl boards were mounted to each side of the vertical slide out. All tools including: bolt cutters, pike pole, pry bar, flat and pick axes, claw tool, and halligan were mounted. Two portable lights were strapped down in the corner of the compartment. No equipment was mounted in the rear, only labels. In the third passengers side compartment, a Chanl Panl board was added to the rear wall of the upper portion of the compartment, and hoses and door spreader were secured. In the lower portion of this compartment, a cutter, spreader, and rams were mounted. A Glasmaster was secured on the side wall. In the second passengers side compartment, three of the Departments existing SCBA brackets were mounted. In the first passengers side compartment, a Chanl Panl rear wall board was added in the upper portion of this compartment and a pocket for saw parts and fuel mix was mounted. A chain saw was also mounted on the shelf in this compartment. In the lower portion of this compartment, a Chanl Panl rear wall board was added as well as a half shelf in the rear of the compartment to hold the Kodiak Jacks. The jacks were secured to the Chanl Panl with rubber brackets and pins. All equipment was labeled with red/white tags. This truck was completed in 2 1/2 days.

Go In-Service

  • Match your equipment to our mounting products listed in our catalog. Custom mounts are available upon request. We will ship all mounting products complete along with mounting hardware. This will allow you to plan, layout, and mount all equipment at your facility.
  • Contact us for help designing boards or configuring cabinets based on your equipment list. We will ship complete boards to you, ready for installation.
  • Send us your apparatus and accompanying equipment and we will do all the layout, fabrication, and installation. Your apparatus will be completely outfitted and ready to Go In Service when it leaves our facility! Contact us for outfitting large fleets as well.